10/31/2022 0 Comments Mweb home loginIf there’s no app, or if you’d prefer to use the router’s browser-based user interface, connect your PC to the router using an ethernet cable. Use it if your new router has one (in some cases, that might be the only way you can configure the router). Many router manufacturers provide smartphone apps for configuring their routers. #Mweb home login password#Step 4: Change your wireless router’s admin password The red cable goes from the router to a PC, while the thinner cable plugged into the green port on the gateway connects to a phone jack in the wall. Michael Brown/PCWorldĬonnect your gateway to your router’s WAN port using a CAT5e or CAT6 cable (the gray cable in this photo). Wait another minute or two for it to boot. Next, plug in your router’s power supply and turn it on. Turn your gateway back on and wait a minute or two for it to boot up. Use it to connect the gateway to your router. If there is no ethernet cable plugged into the gateway’s LAN port, an ethernet cable should have come with your router. If an ethernet cable is plugged into the gateway’s LAN port, unplug it and plug it into your router’s WAN port (once again, some routers have dedicated WAN and LAN ports others have auto-sensing ports). Turn off your gateway (unplug the power supply if there’s no on/off switch). Step 3: Connect your gateway to your new router It has a broadband connector, a phone jack for internet phone service, and a four-port ethernet switch. The Motorola NVG510 is a DSL modem that AT&T sometimes provides its U-Verse broadband customers. You might need to contact your ISP for help with this step, as some won’t allow you to configure the gateway yourself. Some gateways have what’s known as a “bridge mode” for working with a secondary router others handle it differently. If your broadband gateway also has a built-in router, such as this Motorola NVG510, you’ll need to put the gateway’s router into “bridge” or “passthrough” mode to use your own router. Enter the IP address into a web browser to access the gateway’s configuration screen. ( Here’s explanation of double NAT and why you want to avoid it.) You’ll need to know the IP address that the gateway is using (you’ll typically find this on a label on the gateway itself). This is necessary to avoid double-NAT scenarios, among other things. If your gateway has an integrated router, you’ll need to configure the gateway to disable the router and pass the WAN IP address (the unique Internet Protocol address that the ISP assigns to your account) and all network traffic through to your new router. Unfortunately, these integrated modem/routers are usually of much poorer quality than stand-alone routers, and they are unlikely to allow you to build out mesh networks that have multiple wireless access points (or APs) that enable you to blanket your home with Wi-Fi. Most ISPs provide their customers with modems-aka gateways-that have routers built in. Step 2: Configure your wireless router gateway Many newer routers, such as the TP-Link Deco M5 show here, have auto-sensing ethernet ports that configure themselves for WAN or LAN duty based on the signal they receive from the cable. You’ll need to perform some preliminary steps first, so don’t disconnect or turn anything off just yet. Some routers have a designated WAN (Wide Area Network) port for connecting to the gateway, while others have auto-sensing ports that automatically configure themselves as WAN or LAN (Local Area Network, i.e., your home network). Instead, place the node where its wireless signal can reach that dead spot. Mesh systems need not be expensive-our favorite budget pick, TP-Link’s Deco M5 three-pack is just $150.īut, caution: Don’t put a wireless node in a Wi-Fi dead spot-it won’t be able to connect to your network any better than any client device. Your data will wirelessly hop from one node to the next, and you’ll have a strong Wi-Fi signal nearly everywhere in your house. In this system, you locate one node wherever your gateway is, and then place subsequent nodes in different rooms of your home. But there’s also an easier option: a mesh-style router.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |